NMOS & PMOS: Useful Applications

Transistors, specifically MOSFETs, I would say are the second most important component to an EE designer next to the passive compoents (resistors, inductors, capacitors).

I will show you a few useful applications that can be applied using MOSFETs that anyone working in electronics should have in there arsenal.

First lets briefly look at the two variations of MOSFETs.

You have the N-Channel MOSFET below:


Then, you have the P-Channel MOSFET below:

Image - PMOS.png

They have some minor differences in the way they are made and how they are used but in essences they have the same function and operate the same.

Every MOSFET has a Gate-source threshold voltage \Huge (V_\text{GS}).  This is the most important part of the FET because in order to turn on the MOSFET you need to apply a voltage at the gate that exceeds this threshold voltage.  In the datasheet of the MOSFET, you can find this value.

Now, onto the main event:

1. Using them as digitally controlled switches.

One of the most common uses for these FETs is to use them as switches.  When working with electronics, especially with battery operated electronics, you sometimes need to control when certain sensors are turned on or control when certain components get powered on in order to conserve battery power.

Here comes the FETs to the rescue.

You have two ways of accomplishing this task, using either the NMOS or the PMOS.

Note: When using MOSFETs with digital electronics, make sure you get a logic level mosfet.  Meaning that the on voltage for Vgs is between 2V-5V.

Using the NMOS, this is considered LOW SIDE switching because the source pin is connected to ground.


Using the PMOS, this is considered HIGH SIDE switching because the source pin is connected to the device/component instead of ground.


2. Using them as logic level converters[1]

This one mostly applies to the NMOS MOSFET, I haven’t seen a configuration out there with PMOS.

Nowadays with DIY electronics being more and more popular and with a larger community of makers, you have a huge variety of microcontrollers and sensors to make the next big product. With this variant comes a variety of components with different supply voltages, ranging down from 1.8V up to 5V.  The issue with this is trying to match sensor supply voltages with your microcontroller when it comes to communicatong via I2C or SPI or even a single 1 or 0 signal. If you supply a sensor or IC with a higher signal voltage than it can handle you risk damaging the component and rendering it useless.

Here comes the NMOS to the rescue. With an NMOS you can fix this issue by making a 5V to 3.3V logic level shifter to communicate with each other while avoiding any damage.



3. Making a constant current source.

This is one is my favorite application using MOSFETs.  For me I do a lot of testing of DC DC Converters to make sure it meets my design specifications and one test requires I have a constant current that will not fluctuate.  Using this design I am able to set the desired current for my test.

Another application is used for LEDs.  LEDs are a lot different that traditional light bulbs in that instead of operating off a voltage rating, they operate at a current rating.  Essentially you need to maintain a constant current applied to the LED to achieve your desired brightness.


These are some of the three uses for MOSFETs that I normally deal with for my projects.  There’s plenty more but these were my top 3.

If you have any questions, input, corrections, please let me know in the comments below.

Enjoy building :)!

1. Bi-Directional Level Shifting
2. Sparkfun Learning

2 thoughts on “NMOS & PMOS: Useful Applications

    • Hey PRJ, the difference is that transistors are current based and MOSFETS are voltage based. When you apply a voltage higher than 0.7 on a transistor you need to add a series resistor on the base to limit the current. With a MOSFET, the resistance at the gate is in the mega ohm range so you do not need to add a series resistor just a voltage high enough to turn on the MOSFET.

      Another major difference is that the MOSFET is a lot more efficient to use in power related projects because the resistance between the drain and source is in the milli-ohm range essentially acting as a single pole switch. You have a lot more power loss in the transistor.

      If you are still confused and/or you need a little more explanation just let me know ill be happy to elaborate.


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s